Getting Started

git clone https://github.com/lh3/minimap2
cd minimap2 && make
# long reads against a reference genome
./minimap2 -ax map10k test/MT-human.fa test/MT-orang.fa > test.sam
# create an index first and then map
./minimap2 -x map10k -d MT-human.mmi test/MT-human.fa
./minimap2 -ax map10k MT-human.mmi test/MT-orang.fa > test.sam
# long-read overlap (no test data)
./minimap2 -x ava-pb your-reads.fa your-reads.fa > overlaps.paf
# man page
man ./minimap2.1

Introduction

Minimap2 is a fast sequence mapping and alignment program that can find overlaps between long noisy reads, or map long reads or their assemblies to a reference genome optionally with detailed alignment (i.e. CIGAR). At present, it works efficiently with query sequences from a few kilobases to ~100 megabases in length at an error rate ~15%. Minimap2 outputs in the PAF or the SAM format. On limited test data sets, minimap2 is over 20 times faster than most other long-read aligners. It will replace BWA-MEM for long reads and contig alignment.

Minimap2 is the successor of minimap. It uses a similar minimizer-based indexing and seeding algorithm, and improves the original minimap with homopolyer-compressed k-mers (see also SMARTdenovo and longISLND), better chaining and the ability to produce CIGAR with fast extension alignment (see also libgaba and ksw2) and piece-wise affine gap cost.

If you use minimap2 in your work, please consider to cite:

Li, H. (2017). Minimap2: fast pairwise alignment for long DNA sequences. arXiv:1708.01492.

Installation

For modern x86-64 CPUs, just type make in the source code directory. This will compile a binary minimap2 which you can copy to your desired location. If you see compilation errors, try make sse2only=1 to disable SSE4. Minimap2 will run a little slower. At present, minimap2 does not work with non-x86 CPUs or ancient CPUs that do not support SSE2. SSE2 is critical to the performance of minimap2.

Algorithm Overview

In the following, minimap2 command line options have a dash ahead and are highlighted in bold.

1. Read -I [=4G] reference bases, extract (-k,-w)-minimizers and index them in a hash table.

2. Read -K [=200M] query bases. For each query sequence, do step 3 through 7:

3. For each (-k,-w)-minimizer on the query, check against the reference index. If a reference minimizer is not among the top -f [=2e-4] most frequent, collect its the occurrences in the reference, which are called seeds.

4. Sort seeds by position in the reference. Chain them with dynamic programming. Each chain represents a potential mapping. For read overlapping, report all chains and then go to step 8. For reference mapping, do step 5 through 7:

5. Let P be the set of primary mappings, which is an empty set initially. For each chain from the best to the worst according to their chaining scores: if on the query, the chain overlaps with a chain in P by --mask-level [=0.5] or higher fraction of the shorter chain, mark the chain as secondary to the chain in P; otherwise, add the chain to P.

6. Retain all primary mappings. Also retain up to -N [=5] top secondary mappings if their chaining scores are higher than -p [=0.8] of their corresponding primary mappings.

7. If alignment is requested, filter out an internal seed if it potentially leads to both a long insertion and a long deletion. Extend from the left-most seed. Perform global alignments between internal seeds. Split the chain if the accumulative score along the global alignment drops by -z [=400], disregarding long gaps. Extend from the right-most seed. Output chains and their alignments.

8. If there are more query sequences in the input, go to step 2 until no more queries are left.

9. If there are more reference sequences, reopen the query file from the start and go to step 1; otherwise stop.

Limitations

• Minimap2 may produce suboptimal alignments through long low-complexity regions where seed positions may be suboptimal. This should not be a big concern because even the optimal alignment may be wrong in such regions.

• Minimap2 does not work well with Illumina short reads as of now.

• Minimap2 requires SSE2 instructions to compile. It is possible to add non-SSE2 support, but it would make minimap2 slower by several times.

In general, minimap2 is a young project with most code written since June, 2017. It may have bugs and room for improvements. Bug reports and suggestions are warmly welcomed.